AussieLP Gas GrillAssembly and Use ManualFOR YOUR SAFETYIf you smell gas:1. Shut off gas to the appliance.2. Extinquish any open flame.3. Open Lid.4.
STEP 2- FIXED LEG/SIDE TABLE ASSEMBLY TOOLS: •In the same way, attach the Front and Rear Fixed Legs to the remaining Side Table using 1/4” x 1” Bolts
STEP 3- LEGBRACE ASSEMBLY •Attach Legbraces onto each Side Table assembly using 1/4” x 1” Bolts. Do not tighten bolts completely. Tools:AXLE HOLESV
1/4” x 1” BOLT - WOOD LEG1/4” x 1 3/8” BOLT - METAL LEGSTEP 4-BOTTOM SHELF/LEG & CASTER ASSEMBLY•Place Leg/Side Table assemblies opposite each oth
STEP 5-WHEEL/ CYLINDER BRACKET ASSEMBLY•Slide Axle out. With the notched side of Cylinder Bracket down, secure the Cylinder Bracket towheel end of Bot
STEP 6-GRILL BODY/CART ASSEMBLY- KANGA MODELSCAUTION: Some parts inside the Grill Body may have sharp edges or cornersRemove Bottom Body Panel from un
STEP 6-(CONTINUED) ASSEMBLE GRILL BODY TO CART- KANGA MODELS•Turn Grill Body upside down and position between cart legs with the Hose and Regulator on
STEP 7-GRILL BODY/CART ASSEMBLY- BONZA & BONZA DELUXE MODELSNote: Assembly of Grill Bodywill require two people. CAUTION: Some parts inside of Gri
STEP 7-(CONTINUED) GRILL BODY/CART ASSEMBLY- BONZA MODELS•Lay Grill Body on its back side with control panel up. Place Grill Body between legs and Sid
STEP 8-ATTACH DECORATIVE PRIVACY PANEL TO CART - (ALL MODELS)STEP 9-INSTALL BURNER•Remove plastic covering from Burner and remove Cotter Pin from Burn
.•Fit venturi end of Burner through hole in the inside firewall (behind control panel) and onto Gas Control Valve Nozzle (Fig. G & Fig. H). Be car
2IMPORTANT SAFEGUARDSFAILURE TO FOLLOW THESE SAFEGUARDS COULD RESULT IN DEATH, SERIOUSBODILY INJURY, AND/OR PROPERTY LOSS. READ AND FOLLOW ALL INSTRUC
STEP 10-INSTALL BOTTOM BODY PANEL/GREASE TRAY- (ALL MODELS)•In upright position and drain holetoward the rear, slide Bottom BodyPanel into guides (
STEP 12-ATTACH HANDLE TO WEATHER COVER (LID) - KANGA MODELS•Insert two #10 x 3/8” Screws through bottom of Weather Cover into Handle and tighten.21HA
22•Insert Heat Indicator studs intoHood holes and secure using twoLockwashers and two 10-24 Hexnuts. Do not overtighten or you may crack Hood finish.
STEP 14-ATTACH LP CYLINDER TO GRILL - (ALL MODELS)•Fill empty LP Cylinder at your local LP gas supplier.•Set bottom ring of LP Cylinder into Cylinder
STEP 15-LEAK TESTING (TO BE PERFORMED IN A WELL-VENTILATED AREA.)Supplies Needed for a Leak TestClean paint brush, water, and dishwashing liquidHow to
OPERATING AND MAINTAINING YOUR GAS GRILLGAS, CYLINDER, HOSE ANDREGULATOR INFORMATIONThis LP gas grill was designed to use propane gas. Propanecylinder
· Never connect or disconnect LP gas cylinder or fittings while grill is in use or is hot. · When the LP gas cylinder is connected, the grill must be
· Always perform a leak test before each use.· Leak test must be performed in a well ventilated area. · Never perform a leak test on a grill while in
· Wash the porcelain coated Cooking Grids (41) with amixture of hot water and baking soda. · Empty the foil pan and grease tray after each cookingses
· Open Lid or Hood (depending on the model) before lighting the grill to prevent an explosion from gas build-up. · The Lid (Kanga™ series only) must
7. WARNING! If your grill catches on fire:• If the fire is in the grill portion and you can safelyreach the control knobs, then turn them off by tu
Your burners have been preset by the manufacturer for opti-mal flame performance. A blue flame, possibly with a smallyellow tip, is the result of the
Regularly clean your LP gas grill between uses and espe-cially after extended periods of storage. Ensure the grilland its components are cool before
It is not necessary to remove and wash the ceramic bri-quettes in order to keep them clean. Burning off the residueafter each cooking should be suffic
TROUBLESHOOTING ProblemPossible CauseSolutionBurners will not light using the ignitorBurners not assembled cor-rectlyNot pausing long enoughbefore cli
TROUBLESHOOTING ProblemFlames blow outFlare upPersistent grease fireUnable to fill LP tankHumming or whistlingfrom the regulatorPossible CauseHigh or
IMPORTANT NOTICEIMPORTANT NOTICEThe gas grill is setup to operate with a LP Gas Cylinder equippedwith an OPD (Overfilling Prevention Device).This is a
AUSSIE GRILL COMPANYLIMITED WARRANTYThis product is warranted to the original consumer purchaser against defects in material and workman-ship under no
— NOTICE —AUSSIE GRILL COMPANY STRIVES TO BE A QUALITY SUPPLIER OF CONSUMER PRODUCTS. IF WE INADVERTENTLY OMITTED ANY PARTS NEEDED FOR ASSEMBLY, OR YO
ASSEMBLY INSTRUCTIONS for KANGA, BONZA, and BONZA DELUXE MODELSPREPARATION FOR ASSEMBLY: Removing parts from carton and some assembly will requiretw
111213141516171819202122232425Part#*See BottomPage Note*See BottomPage Note03.6091.0303.6092.03*See BottomPage Note*See BottomPage Note03.5989.0003.60
262728293031323334353637383940PART#03.6094.0003.5996.0003.5997.0003.5998.0003.5999.00*See BottomPage Note03.4074.0003.4066.0003.6003.00*See BottomPage
414243444546474849505152535455PART#03.6015.0003.5023.0003.6016.0003.6017.0003.5024.0003.6020.00*See BottomPage Note03.6023.0003.4070.0003.5033.0003.50
STEP 1- WHEEL LEG/ SIDE TABLE ASSEMBLYTOOLS:•Note: There are three side table designs used depending on the model: Square SideTables (Item 1) which ca
Comentários a estes Manuais